The TNC or TNCE cards are provisioned as active and standby in the NCS 2006 shelf, and as a stand-alone card in the NCS 2002 shelf. The MF-4X4-COFS patch panel supports only fixed grid and can support up to 96 channels. NCS2K-S, NCS2K-F, and NCS2K-L packages are not supported in ONS 15454 M12 during upgrade from any release preceding to R11.x Lists the cards that are supported in Flex NCS and Fixed Grid NCS nodes. Node that supports Flex Spectrum functionality and up to 96 channels in theįixed Grid NCS Node: Node that supports fixed 80 channels in the ITU-T C band. Platform and Software Release Compatibility for Control Cards Port is available on all control cards except the TNCS-2 and TNCS-2O cards. The DB-9 console port also does not work in control cards installed in the sub-tending shelves. The DB-9 console port of the node controller works only on the active control card of the GNE or ENE and not on the standbyĬontrol card. This chapter describes the common control cards needed for theĬisco NCS 2000 Series platforms and provides installation and card turn up Single Shelf Control - Downgrade Control Card with Software prior to Release 11.0.Dual Shelf Control - Downgrade A Single TNCS-2 or TNCS-2O Card to the TNC, TSC, TSC-E, TNC-E, TNCS, or TNCS-O Card.

Dual Shelf Control - Downgrade Control Cards to TNC, TSC, TSC-E, TNC-E, TNCS, or TNCS-O Card.Downgrade the TNCS-2 and TNCS-2O Cards to TNC, TSC, TSC-E, TNC-E, TNCS, or TNCS-O Cards.Single Shelf Control - Upgrade Control Card with Release 11.0.Single Shelf Control - Upgrade Control Card to TNCS-2 or TNCS-2O Card.Dual Shelf Control - Upgrade Control Card to TNCS-2 or TNCS-2O Card.Dual Shelf Control - Upgrade the TNC, TSC, TSC-E, TNC-E, TNCS, or TNCS-O Card to the TNCS-2 or TNCS-2O Cards.Upgrade the TNC, TSC, TSC-E, TNC-E, TNCS, or TNCS-O Card to the TNCS-2 or TNCS-2O Card.Insert an LCD/ECU of Release 11.0 in a Release prior to 11.0 Chassis.Insert an LCD/ECU of Release prior to 11.0 in a Release 11.0 Chassis.NTP-G278 Upgrade an Older Controller Card to a Newer Controller Card.Accessing and Configuring the Controller Cards Using Link-Local Address.DLP-G774 Changing the Frame Type on the OSC.

DLP-G788 Configuring Operating Mode for the TNC, TNCE, TNCS, TNCS-O, TNCS-2, and TNCS-2O Cards.DLP-G606 Configuring UDC and VoIP for the TNC, TNCE, TNCS-2, TNCS-2O, and TNCS/TNCS-O Cards.DLP-G605 Provisioning PPM and Port for the TNC, TNCE, TNCS-2, TNCS-2O, and TNCS Cards.DLP-G604 Installing the TNC, TNCE, TSC, TSCE, TNCS-2, TNCS-2O, TNCS-O, or TNCS Card.NTP-G313 Installing and Configuring the TNC, TNCE, TSC, TSCE, TNCS, TNCS-O, TNCS-2, and TNCS-2O Card.Related Procedures for TNCS and TNCS-O Cards.Operating Modes for TNC, TNCE, TNCS, or TNCS-O cards.Related Procedures for TSC and TSCE Cards.

Related Procedures for TNC and TNCE Cards.

Udc start hardware reset upload mode